Black Collectible Display Show Case Illumicase+ with LED Lights and Mirror Base and Back for 1:64 1:43 1:32 1:24 1:18 Scale Models

Always a good buy and fit for my things. Good value for my 1:18 scale cars.

Stupidly simple to assemble. All the panels have protective film on them to peel off right before placing together.Steps to assemble:1. Unpack everything from the box.2. Open the bottom and peel off the film from bottom. Place bottom on a hard, flat surface with the U shaped notch towards you.3. Locate the posts labeled "Back", and place them in the corners of the bottom farthest from you, and slide them into place.4. Locate posts labeled "Front", and place them so that the Groove side of the post is on the side, not the front, and slide them into place.5. Locate one of the 2 square side windows, noting which side is up and peel the protective film off both sides.6. Slide the side piece into the groove on one of the sides.7. Repeat steps 5 & 6 for the other side.8. Locate the mirrored back, remove the film and place into the back groove.9. Locate the top and remove the film from top and bottom.10. Place the top over the 4 posts with the switch facing you, and snap down into place.11. Place whatever items in through the front of the case.12. Locate the front window. Peel off the protective film from both sides.13. Slide front pane into place.14. Plug in the USB, and turn on the switch.After reading some of the reviews, I felt I needed to explain the directions 😅Honestly, stupid simple to assemble, but really a very nice presentation that allows access to the inside from the front, and really shows off 1:18 car.Looks more expensive than what it actually is.Highly recommended!

The media could not be loaded. Such a perfect display for your die cast cars but the “glass” is just plastic that ‼️SCRATCHES EXTREMELY EASILY‼️ (DO NOT USE MICROFIBER CLOTHS EVEN. I used a cloth same to clean glasses) The stickers used to ship left a hard residue on the plastic that was hard to get off without leaving swirls on it as you can see from the pics. MAKE SURE TO PAY ATTENTION TO THE DIRECTION OF THE POSTS WHEN ASSEMBLING, to make sure the front part can slide in and out to remove the cars because once it’s built YOU CANNOT TAKE IT APART WITHOUT BREAKING IT (which I accidentally did lol but I’m not mad about it ,user error). All this aside the display is quite perfect and would make a great gift for a car enthusiast 🙏🙏

Better than I expected.

This thing is sharpI used it for my 1/18 scale gmp mustang and it looks very good! It is a great way to display while protecting your investment.

When I received it - it was in a flat box, this is because all the sides are laying flat. The kit is easy to assemble and the instructions show you how to put it together. The LED lights are housed in the top of the display. The pieces are wrapped in plastic to protect them in shipment. The lights are powered by 5 volt USB connector with a 36 inch cord, there is no battery box. The lights are very bright and it looks very nice! I used a small amount of clear silicone or RTV to the tire bottoms to keep it from moving around in the display. I am very pleased with how it turned out and will probably order another for my other 59 Corvette soon! Hope this helps! Pictured is a 1932 Ford 1/18 scale ETRL Diecast. 👍

I LOVE this case!! Ligtweight, easy to assemble, and looks fantastic! I had to replace the first one, but it was my fault. The mirror and clear plastic panes are VERY delicate and scatches easily! DO NOT attempt to clean it by using any sort of cleanser, spray or the like (e.g., Windex, Lysol Cleanser, etc.). You will permanently damage the mirror and clear panes. Even very soft tissue will scratch it. Trust me on this as I learned the hard way. To remove any dust that will accumulate, I only apply very short bursts from an air canister held at least 7-10 inches away.I lights my model full and brightly from every angle (see photos). The LEDs are nicely hidden from view and are VERY bright. To secure the model and accessrories shown, and to prevent them from moving, I just applied a touch of clear silicone and carefully removed any excess prior to displying the finished product. I will be purchasing more cases to display my other models. It might be a bit more pricey than other lightedr cases, but definitely worth the price in my opion.

Had to return. Hopefully the replacement is better. The Ford Plastic, Support, Beans, Very Week and One arrived broken. Let’s hope the replacement is better. The light fixture is very weak. Not very bright at all.