Trim-Lok Drip Rail, White – 1/2” Height, 25’ Length – PVC Plastic Rain Gutter for Cars, Vans, and RVs, Easy to Install Flexible Drip Rail Molding to Control Water Runoff, Durable 3M Tape Included

This is my second order of this product. First order went across a whole bank of louvered windows and has held up almost a year without budging taking full sun and heat, freezing winter temps.Just installed another gutter on my corrugated aluminum 5th over a bank of large side windows, will do the other side today. The tape backing is VERY sticky once set so get it right the first time or loosely press in place every few inches to test, otherwise you can leave part of the black sticky tape on your RV.Someone asked can this be curved down around windows several inches - yes it can - and also over thick corrugated aluminum! Lay it in the sun, get it nice and soft, or have a heat gun handy and gently heat the end you want curved plus heat your metal trailer wall. It will conform like butter. Peel tape back only a few inches at a time, press in place, then rub with a smooth rounded end tool of some type, paint brush, wrench, something smooth, and slowly work across. If you want to get fancy, get up there with a small level and check that you're laying it so water will run well, or, make a high spot in the middle so water runs easily to both gutter ends.This product is fabulous for do it yourself gutters and especially if you live in an area where it rains hard. You can never go wrong adding more gutters over major windows, doors etc. I've read all the reviews here and can't figure out how people could complain. Yes, it comes coiled up in a box but it will flatten out nicely in heat or sunshine. Simply extend it out on your lawn until good and pliable. As for people complaining that it doesn't stick and falls off - I have a very hard time seeing that happen as once you firmly press it in place, it is on tight. Maybe slick fiberglass covered in some kind of wax product but I doubt that would stop this tape from sticking. If I can make it stick on 90 to 180 degree curves in places than I suspect anybody can. Clean your rig with alcohol/ water half half where you want the gutter, I pass over that with my heat gun afterwards, start laying it out just a few inches peeling tape backing slowly, press hard with fingers and or rounded end tool, done. It's not moving! Great product for the price!

I used this strip to divert rain water from above our doors on a Trawler power boat. The strip is rolled fairly tightly for shipping and works best if it has been unrolled and allowed to straighten at room temperature before applying it to a surface. It can be gently heated with a hair dryer so that it will become straight. I also found that it can be reverse curved (bent back against the "J" drain) to follow a curved surface and remain attached.I found the material easy to apply (take your time to get it straight) and the adhesion to my surfaces cleaned carefully with acetone (Ladies Fingernail polish remover is great!) and rinsed with a damp rag and dried was excellent. The material adheres instantly but can be pulled off and placed again until straight. Once fully applied and pressed into place for about a minute it cannot be easily removed. The material uses a kind of double backed tape that attaches to the molded J drain and the RV or Boat surface. This material typically requires a razor blade knife to fully remove it once it is attached and can be considered permanent.

This works great above the windshield of my Class A motor home to prevent water from running down and leaving streaks on the glass, especially from dew running off the roof at night. But the first install didn’t work well. Water seeped into the adhesive and it came loose very quickly. Also the small gap along the top collected a lot of dirt. Seeing the problem I removed it and installed a new piece and then sealed the top edge with a bead of silicone. Problem solved and it works great now. No more constantly having to clean the windshield!

OK, this is the BOMB!, has saved me so much work. I put a strip directly above the huge windshield on my Class A RV to channel water and dripping dew away from the shield and too the sides. This has totally eliminated the dark and dirt streaks from the glass. Every morning on the road I would have to get out the ladder and clean those streaks off the windshield, a 15-20 minute process, which I am happy to say I no longer have to do. The channel sticks very well after cleaning the surface with mineral sprites, and will curve enough to follow around the top of the shield. Be careful to position it right the first time as once stuck it is there for good, peel off the backing a foot or so at a time and align with the rubber windshield gasket. Looks OEM and does the job, a bit expensive and I wish it was in 10' lengths but it is what it is, I now have extra. Haven't gone thru a hot summer yet but I expect it will stay stuck as the 3M adhesive is the same used for car emblems.

I purchased this Drip Rail to help with water management when it rains and prevent any water from trickling down above the bunk ends on my Rockwood Roo. It seems to help keep the flow. It is flexible as you put it on the camper and it looks nice. I mounted the rail last fall and it still looks brand new. The tape peels right off and installation was as easy as could be. I'd recommend this for anyone who wants to manage the water flow outside of their camper.

Cleaned trailer very well, temps were in the mid 80’s, mild humidity. Had to go back and re-apply several times throughout the day; now it’s not straight and water doesn’t follow out to the ends, it pools and over flows the channel.

I used a different brand to catch water and stop a leak over one of the storage doors on my camper. It worked great. This brand however, no good. All of the ones I cut and installed did not stick. I followed instructions, I let it get hot on the sun so it was more flexible, I thoroughly cleaned the camper’s surface, but none of them stuck. Most peeled the next day. Some peeled a couple days later. I definitely would not buy this product again.

J'ai juste hâte de l'installer, tanné des cernes durs à laver

I put two sections on the boat to stop drips from the upper deck. Worked great so I just bought to more sections

This drip guard works well. Make sure to clean the surface before you apply the drip guard. The 3M tape on the back is an apply once only. EXTREMELY STICKY. You can not remove it once it’s been stuck on.

I bought the item to renew the gutter on my campervan but have not fitted it yetit appears to be ideal for the purpose but until it has been fitted I cannot say more

Using on our Northern Light camper and so far the gutters are working well.