Crystal Clear Epoxy Resin Two Gallon Kit | MAS Tabletop Pro Epoxy Resin & Hardener | Two Part Kit for Wood Tabletop, Bar Top, Resin Art | Set Includes Spreader & Brush | Professional Grade (2 Gallon)

This was our very first project using epoxy and man it was a huge undertaking. Our project was a 10ft long, 3 inch thick, 22 in wide slab of cypress. . Mas epoxy was easy to mix, don’t think you could mess it up. The river we poured was simply beautiful with the mica powder added to it. Then after letting that dry we deep poured the entire board/bar. We had underestimated the amount of epoxy we would need because on the deep pour it actually floated the board and so we weren’t expecting to fully cover or encase the bottom also. But we ordered more and done a 2nd pour as per the instructions and our project turned out pretty good for our first time. My advice is if you think it’s gonna take one gallon order two. Better to have to much than not enough. Our project took 6 gallons.

I used this epoxy to make a live edge table. I ripped the flitch in half and turned both live edges in to the middle to make a table top with square edges on the outside and live edge in the middle. Some call it a river table. The wood was two inches thick and 40 inches long. I filled the live edge gap in several small pours, no larger than a quart. The epoxy is very clear and bubble free in small pours.

I bought this epoxy to use for a river table because I couldn’t find any deep cast material available. The finished product came out nice but this epoxy is much thicker than others I’ve used. Definitely better for projects like it’s intended for with table tops. Much harder to get out the entrapped air due to the viscosity. This product would be great for when you don’t want the epoxy to level too quickly and run all over the place. Make your Deep Pour Epoxy available on Amazon.

Stop....stop right there, look no further! If you are looking for the best epoxy out there, you have just found it. I have tried just about every epoxy out there, and this MAS Table Top Epoxy is by far, the absolute best. This epoxy is nice and thick, easy to mix, easy to pour and cures to a beautiful, crystal clear, super shiny finish! You will not be disappointed with this epoxy.

I have found a bucket of play marbles that belong to my partner. since I had no heart to give all of them away (not sure why, but he did keep them for 40 years) I decided to create something special for him. I inserted the marbles in the old table. I covered it with MAS Tabletop Pro Epoxy Resin & Hardener. Two layers of MAS Tabletop Pro Epoxy Resin & Hardener. I used 2.6 gallons for 3X6 table (The marbles were not completely flush). I received installation instruction after the purchase. Customer service was very helpful when I had a question. One thing that no one is talking about is; AFTER YOU MIX IT and ready to use, the epoxy is STICKY!!! Make sure your space is protected, if it drops on your floor it will be very hard to clean (ask my cat that had to have a hair cut) If you are first-timer, USE GLOVES. I recommend to follow the instructions and watch a video or two before you start.The results are beautiful. The tabletop looks like glass.If you are wondering about the paw that is in the middle on the left... the same cat that had a hair cut jumped on the table between the layers (I let her out of the room too soon) I painted one paw mark with a Sharpie before the second layer.

I used this product for 2 applications: first was a river table pour for a 4ft x 2ft coffee table with about a 6-7in moat that I did in 1/4th inch pours (w/ 2 hours in between each pour), with 5 pours in total for the 5/4ths inch thick board. This came out pretty well, with only a few bubbles that were leftover even after using a heat gun.The second use, however, which came about 2-3 days after the above project was conducted, didn't turn out so well. Using the remainder of the 2-part materials, I attempted to flood coat a section of the walnut wood board that had some imperfections and deep divots. However, this time the pour resulted in the resin not hardening sufficiently (even after following the exact same instructions as stated above when it worked perfectly), which resulted in me ruining the piece of wood and having to try to scrape off the whole entire coat because it never set properly, rendering it unusable.In the future, I would only recommend the product if you're confident that you need this much volume in one go; otherwise, I can't trust keeping the epoxy hardener combo jugs on the shelf and expect the same result with any remaining material.

First time using MAS products and I was surprised how informative they were. I received emails before product arrived with important instructions about working with the product, prepping my project and ensuring I had the proper working temperatures for a successful outcome. When the product arrived on time, it came with same instructions again and of course the phone numbers for assistance and reassurance.READ YOUR INSTRUCTIONS! I’ve worked with Epoxies before and they all differ a little bit. This project came out great!

Mixed the product as directed and the finished results were fabulous. The only issue I has was I did not get my base color dark enough(my Bad). The finish hardened pretty quickly and glossy. The project only took a couple of days and I am very happy with the surface. For my first try I was pleased with the end results. Tap your plastic really well and have fun with the color additions.